标准材质使用范围 材质:标准材料RN809 使用温度： -45℃~+100℃. 适用压力:≤20Mpa,线速度 0.5M/S 适用介质流体:一般石油液压油,低温用石油液压油为介质的工作油 特性：与SKY密封件沟槽互换的活塞专用/活塞杆专用件。由于可以在-45~+100℃ 时使用，因此，即使是在寒冷的地区，也无需更换密封件。此外采用了比其他U型密封件更不易发生粘滑的设计，由于重视了耐寒性，限制了橡胶的硬度，请注意在高压/高频的条件下使用 主要用途：起重机，高空作业车用油缸，耐寒规格油缸 (T)SNYパッキン寸法表 パッキンおよびみぞ寸法 (単位：mm） 指示コード d D H GA GB d1(参考) 標準 （RN809） 併用バック （PT111） 14 22 5 5.7 6.7 14.4 2.5 (T)SNY-14 TCS-22×14 18 26 5 5.7 6.7 18.4 2.5 (T)SNY-18 TCS-26×18 20 28 5 5.7 6.7 20.4 2.5 (T)SNY-20 TCS-28×20 25 33 5 5.7 6.7 25.4 2.5 (T)SNY-25 TCS-33×25 28 35.5 5 5.7 6.7 28.4 2.5 (T)SNY-28 TCS-35.5×28 30 40 6 7 8.5 30.5 3 (T)SNY-30 TCS-40×30 31.5 41.5 6 7 8.5 32 3 (T)SNY-31.5 TCS-41.5×31.5 35 45 6 7 8.5 35.5 3 (T)SNY-35 TCS-45×35 35.5 45 6 7 8.5 36 3 (T)SNY-35.5 TCS-45×35.5 40 50 6 7 8.5 40.5 3 (T)SNY-40 TCS-50×40 45 55 6 7 8.5 45.5 3 (T)SNY-45 TCS-55×45 45 56 7 8 9.5 45.5 3 (T)SNY-45A TCS-56×45 50 60 6 7 8.5 50.5 3 (T)SNY-50 TCS-60×50 55 65 6 7 8.5 55.6 3 (T)SNY-55 TCS-65×55 56 66 6 7 8.5 56.6 3 (T)SNY-56 TCS-66×56 60 70 6 7 8.5 60.6 3 (T)SNY-60 TCS-70×60 60 71 7 8 9.5 60.6 3 (T)SNY-60A TCS-71×60 63 73 6 7 8.5 63.6 3 (T)SNY-63 TCS-73×63 65 75 6 7 8.5 65.6 3 (T)SNY-65 TCS-75×65 70 85 9 10 12 70.6 4 (T)SNY-70A TCS-85×70 70 80 6 7 8.5 70.6 4 (T)SNY-70C TCS-80×70 75 85 6 7 8.5 75.6 4 (T)SNY-75 TCS-85×75 75 90 9 10 12 75.6 4 (T)SNY-75A TCS-90×75 80 95 9 10 12 80.6 4 (T)SNY-80A TCS-95×80 80 90 6 7 8.5 80.6 4 (T)SNY-80C TCS-90×80 85 100 9 10 12 85.6 4 (T)SNY-85 TCS-100×85 90 105 9 10 12 90.6 4 (T)SNY-90 TCS-105×90 95 110 9 10 12 95.6 4 (T)SNY-95 TCS-110×95 100 115 9 10 12 100.6 4 (T)SNY-100 TCS-115×100 105 120 9 10 12 105.6 4 (T)SNY-105 TBC-0105001T111 110 125 9 10 12 110.6 4 (T)SNY-110 TCS-125×110 115 130 8.5 9.5 11.5 115.6 4 (T)SNY-115B TBC-0115002T111 125 140 9 10 12 125.7 4 (T)SNY-125 TCS-140×125 140 155 9 10 12 140.7 4 (T)SNY-140 TCS-155×140 150 165 9 10 12 150.7 4 (T)SNY-150 TCS-165×150 160 175 9 10 12 160.7 4 (T)SNY-160 TCS-175×160 180 200 12 13 15.5 180.7 5.5 (T)SNY-180 TCS-200×180